Wall Pack Accessories

Polycarbonate shield or wire guards for Wall packs.

Gooseneck mount for LED Wall pack

Die cast sensor & floodlight mounting plate fits round, rectangular, octagonal, recessed & surface mount boxes. Lower hole offers better sensor mounting position. 3 close-up plugs, thick, weatherproof gaskets, universal mounting bar and Hanging Helper Hook provided.

Bring convenient power outlets outdoor safely. These heavy die cast covers with spring-loaded lids and weather seal gaskets keep water out. Fits all duplex receptacles in single outlet boxes. Epoxy powder coated.

Die cast aluminum wiring box with weatherproof gasket, ground screw, and two sturdy lugs for wall or ceiling mounting. Die cast aluminum cover without center hole supplied with 4 stainless steel screws.

Die cast rectangular covers with one or three 1/2" threaded holes. Fits FS, cast and recessed single outlet boxes. Supplied with thick foam rubber gasket and two #6-32 stainless steel screws. 3 hole cover comes with one die cast 1/2" close-up plug.

For weatherproof safety, these stamped aluminum covers fit single (CR1) and double (CR2) outlet boxes. Supplied with thick weather seal gaskets and mounting screws.

Die cast aluminum wiring box with ground screw, and two sturdy lugs for wall or ceiling mounting. Supplied with four color matched close-up plugs.

Die cast aluminum for thru-wall or conduit end floodlight mounting. Three 1/2" threaded holes. Side opening cover for easy access and splicing. 1/2" thru wall tapped hub.

Die cast aluminum wiring box with weatherproof gasket, ground screw, and two sturdy lugs for wall or ceiling mounting.

Die cast round covers with one or three 1/2" holes. Fit 4" round boxes. Supplied with thick foam rubber gasket and two #10-24 stainless steel screws. 3 hole cover comes with one die cast 1/2" close-up plug.

Fits covers and boxes to provide weatherproof seal. Precision die cast with clean threads. Plugs accept both Phillips and slotted screwdrivers for easy installation. Choose the diameter and color to fit your application.

Sand cast aluminum "Y" adapter mounts two floodlights in a single 1/2" threaded hole.

Die cast aluminum wiring box with weatherproof gasket, ground screw, and two sturdy lugs for wall or ceiling mounting.

Die cast aluminum with two unique "flex-lugs" for wall or pole mounting of outdoor outlets, switches or floodlights. Ground screw and close-up plugs provided. Cubic capacity is 30.5 cu. inches.

Ground Fault Interrupter duplex outlet covers for vertical or horizontal installation on single outlet boxes. Heavy die cast covers with spring loaded lids and thick weather seal gaskets.

Aluminum trough holds up to 7 Floodlights for full 360?gasketed coverage from a single location. Trough measures 11" long. Five 1/2" tapped hubs on top, 3 on bottom, 1 on side.

For weatherproof safety, this heavy duty die cast aluminum cover fits round boxes. Supplied with heavy foam rubber gasket and four #10-24 stainless steel screws.

Die cast aluminum with two unique "flex-lugs" for wall or pole mounting of outdoor outlets, switches or floodlights. Ground screw and close-up plugs provided. Cubic capacity is 18.3 cu. inches.

Aluminum Pole Slipfitters for mounting fixtures or boxes to top of poles or posts. 1/2" top tap standard. 3/4" top tap on R5-3/4 and R7-3/4 only. Set screws provided.

Die cast aluminum wiring box with weatherproof gasket, ground screw, and two sturdy lugs for wall or ceiling mounting. Die cast aluminum cover with three 1/2" holes supplied with 2 stainless steel screws and one close-up plug.

Rectangular cover with three 1/2" threaded holes. Fits FS, cast and recessed single outlet boxes. Supplied with thick foam rubber gasket. One molded 1/2" close-up plug and (2) stainless steel screws.

Corrosion-proof round four hole cover. Tough polycarbonate with molded-in color. Fourth hole is perfect for motion sensor mounting. Fits 4" round boxes. Supplied with thick foam rubber gasket. One molded 1/2" close-up plug and (2) stainless steel screws.

Available in four configurations, RAB in-line connectors enable RAB fixtures to be mounted to an assortment of RAB arms. Connectors come in black, white and bronze to match RAB fixtures.